Heavy Duty Binary / Gray Output Converter NCV-40H

Description

Heavy Duty NCV-40H

NCV-40H is digital binary or gray code output converter which is connecting with heavy duty ABSOCODER position sensors

NCV-40H[1]N[2]

[1]Output code

Code	Output code
B	Binary
G	Gray

[2]Applicable sensor

Code	Applicable sensor
M5	MRE-1024S16TS100

Item	Specification
Power supply voltage	24VDC±10% (including ripple)
Power consumption	10W or less
Insulation resistance	20MΩ or more between external DC power terminals and ground (by 500 VDC insulation resistance tester)
Withstand voltage	500 VAC, 60Hz for 1 minute between external DC power terminals and ground
Vibration resistance	20m/s² 10〜500Hz, 10cycles of 5 minutes in 3 directions, conforms to JIS C 0040 standard
Ambient operating temperature	0 ～ +55℃ (No freezing) (Surrounding air temperature rating of 55℃ maximum)
Ambient operating humidity	20 ～ 90 %RH (No condensation)
Grounding	Must be securely grounded (ground resistance of 100 ohm or less)
Construction	Book-shelf type within enclosure, DIN rail mountable
Outside dimension (mm)	39(W)×155(H)×93(D) Refer to dimensions for details.
Mass	Approx. 0.4kg

Item	Specification
Converter model	NCV-40HBNM5, NCV-40HGNM5
Number of detection axes	1
Position data sampling time	0.1ms
Status output signal	Latch pulse (Position data reading timing) : 1 point System ready : 1 point Error : 1 point
Input signals	Position data hold signal : 1 point Zero point setting signal : 1 point Error clear signal : 1 point
Front panel function	Zero point setting, error clear
Switch (on rear face of product)	Position data increase/decrease direction setting (CW / CCW) : 1point
	Position data update cycle	Edge timing	0.1ms
			0.2ms
			0.4ms
			0.8ms
		Level timing 1	0.8ms
			1.6ms
			3.2ms
			6.4ms
		Level timing 2	3.2ms
			6.4ms
			12.8ms
			25.6ms
			51.2ms
	HOLD signal format	Transparent format
	HOLD signal format	PC synchro format
	LP signal logic (Non-inverted/Inverted): 1 point
	Zero point setting function selection (Enabled/Disabled): 1 point
	Clearing method setting of the sensor disconnected error (auto clearing / manual clearing): 1-point
Monitor LED	Output state monitor	Position data output, System ready output, Error output
	Input state monitor	HOLD input, zero point setting input, error clear input
	Error state monitor	Sensor disconnected error, Memory error, Low power error, Sensor power supply error, Switch setting error

Item		Specification
Converter model		NCV-40HBNM5, NCV-40HGNM5
Applicable sensor		MRE-1024S16TS100
Total number of turns		1024
Divisions/Turn		65536(2¹⁶)
Total number of divisions		67108864(2²⁶)
Position detection format		Absolute position detection
Max. sensor cable length	5S-SLA	300m
Max. sensor cable length	5S-RBT	100m

Item			Specification
Converter model			NCV-40HBNM5, NCV-40HGNM5
Input	Input signals		HD (Position data HOLD) : 1 point ZPS (Zero point setting signal) : 1 point CLR (Error clear signal) : 1 point
	Input circuit		DC input, photo-coupler isolation
	Input logic		Negative logic
	Rated input voltage		12 ～ 24VDC (10 ～ 30VDC)
	Rated input current		10mA (24VDC)
	ON voltage		10VDC or more
	OFF voltage		2VDC or less
Output	Output signals	Position data	D0〜D25: 26points
	Output signals		LP (Latch pulse: position data reading timing): 1 point NOR (System Ready) : 1 point ERR (Error): 1 point
	Output circuit		Transistor (open drain sink) output, photo-coupler isolation
	Output logic		Negative logic
	Rated load voltage		12 ～ 24VDC (30VDC max.)
	Max. load current		50mA / point
	Max. voltage drop when ON		0.8 V or less